The T200 is ready to load in the most compact design to date while taking up minimal space in the pit area. The charger only takes up about the same amount of bench space as a pair of battery packs and delivers a dedicated 100 W of integrated power per each of the two complete charging circuits. Inside the case is enough transformer power to charge two batteries simultaneously at up to 12 amps each, so you can pump life into anything from a receiver pack to a 6S LiPo or 15S NiMH or NiCD. All the programmability you'd expect from a modern, higher-end charger is built in! The charger comes with the charging algorithm for the most common battery chemistries: LiPo, Li-Ion, LiHV, LiFe, NiMH, NiCD and Pb (lead acid). With the almost de facto standard on the XT60 * interface, connection prevents reverse polarity and guarantees super solid connection. * Powered by the original high-temperature Nylon XT60, manufactured by AMASS, which can handle over 60A of current for extended periods without exceeding 80℃ thanks to their gold-plated spring pins better contact surface. The AGM (Absorbing Glass Mat) battery is maintenance free, provides good electrical reliability and is lighter than the flooded lead acid type. However, AGM batteries are much more different than lead batteries. Although both have the same essential components, they have different chemical structures that make them very different from each other. Never take the risk of charging AGM batteries with a regular charger in normal Pb mode. The SkyRC T200 has the so-called AUTO function which adjusts the supply current during charging or discharging. Especially for lithium batteries, it can prevent overcharging that can lead to an explosion due to user error. It can disconnect the circuit automatically and alarm once detected any fault. All programs for this product were controlled by two-way coupling and communication to achieve maximum security and minimize the problem. All settings are user configurable! The panel with five buttons and the brightly backlit LCD screen make charging a breeze even for beginners. The charger programs with the same logic as many other chargers from SkyRC, so it will be familiar to many users. But even if the T200 is your first programmable charger, you'll find it easy to learn. Users simply scroll through the parameters, use the up/down keys to adjust the values, and then click a key to enter. After going through the manual, you will have it down. Terminal Voltage Control (TVC) The charger allows users to change the terminal voltage (for expert users only). Power: DC Input Voltage: 11-18V AC Input Voltage: 100-240V Charge Wattage: 100W X 2 Discharge Wattage: 10W Battery Capacity Range: NiMH/NiCd: 100-50000mAh LiPo/LiIon/LiFe/LiHV: 100-50000mAh Pb: 100-50000mAh Charging Voltage: NiMH/NiCd: Delta peak detection LiPo: 4.18-4.25V/cell LiFe: 3.58-3.7V/cell Pb: 1.8-2.0V/cell LiIon: 4.08-4.2V/cell LiHV: 4.25-4.35V/cell Discharge Cut-off Voltage: NiMH/NiCd: 0.1-1.1V/cell LiPo: 3.0-3.3V/cell LiFe: 2.6-2.9V/cell LiIon: 2.9-3.2V/cell LiHV: 3.1-3.4V/cell Battery Cut-off Temperature: 20ºC / 68ºF-80ºC / 176ºF (adjustable) Reading Voltage Range: 0.1-26.1V/cell Charge Current: 0.1A-12.0A Discharge Current: 0.1A-2.0A Balance Cells: 2-6 cells Balance Current: 500mA/cell Safety Timer: 1-120 minutes off Charge Method: CC/CV for lithium types and lead(Pb) batteries Delta-peak Sensitivity for NiMH/NiCd. Memory: 10 different charge/discharge profiles